Search found 12 matches
- Mon Jun 08, 2015 9:12 am
- Forum: For Sale
- Topic: Vp v8 355 ( 304 ) for sale
- Replies: 0
- Views: 3263
Vp v8 355 ( 304 ) for sale
Injected 355 for sale approx. 120,000km. Was in 80 series landcruiser tourer in front of an auto, has not been dusted, cooked or flogged rev limiter set to 4400. Gone to diesel to increase range while towing. Engine complete except for flex plate. Comes fitted with HQ sump & earlier 308 oil pump...
- Thu May 21, 2015 2:13 am
- Forum: For Sale
- Topic: FS: Universal Speedo Correctors
- Replies: 51
- Views: 145236
Re: FS: Universal Speedo Correctors
A bit more info ; Reluctor picks up 25 pulses per engine revolution(Isuzu 4bd1t) & the tacho is a 1990 fj80 landcruiser, originally points and wants to see 3 pulses/rev so some sort of correction would be required. Tacho works fine with vp v8 hooked to it but I suppose that would have similar in...
- Sat May 16, 2015 9:20 pm
- Forum: General Tuning Discussion
- Topic: 3082 for auto lockup control only behind a diesel
- Replies: 6
- Views: 3644
- Fri May 15, 2015 11:07 pm
- Forum: General Tuning Discussion
- Topic: 3082 for auto lockup control only behind a diesel
- Replies: 6
- Views: 3644
Re: 3082 for auto lockup control only behind a diesel
Thanks for the feedback VL400, Sounds like it's a go. Already got vss fitted, just got to fab up a tps bracket. Can you scale the TPS? Would it be "TPS-TPS Full Travel - worst case minimum voltage" scaler? It may only end up having 50* of movement from idle to full throttle. I'll set it up...
- Fri May 15, 2015 9:33 am
- Forum: General Tuning Discussion
- Topic: 3082 for auto lockup control only behind a diesel
- Replies: 6
- Views: 3644
Re: 3082 for auto lockup control only behind a diesel
Thanks for the reply Jayme It's an old school 4bd1t isuzu diesel, no vacuum, no electronics, just boost. The aftermarket Tcc controller uses a tps sensor & vss. I thought TCC load was just calculated using tps vs. vehicle speed lock & unlock tables, & delta tps. Is Map used in the calc f...
- Fri May 15, 2015 3:03 am
- Forum: For Sale
- Topic: FS: Universal Speedo Correctors
- Replies: 51
- Views: 145236
Re: FS: Universal Speedo Correctors
Would this work to convert engine tooth reluctor input to tacho signal out on diesel conversion?
- Fri May 15, 2015 2:40 am
- Forum: General Tuning Discussion
- Topic: 3082 for auto lockup control only behind a diesel
- Replies: 6
- Views: 3644
3082 for auto lockup control only behind a diesel
Could I use a '165 ('3082) or 808 with 12p to control converter lockup only on 700r4 behind a diesel? & What inputs would I need? VSS ? TPS ? Engine Rpm ? As I have all the delco bits available, it seems a bit silly to go out & buy some half baked controller for a few hundred dollars. I real...
- Tue Nov 16, 2010 7:27 am
- Forum: Holden ALDL ECUs
- Topic: Can't Get Stable Connection - VX II - OSE En.. & Bin Dumping
- Replies: 22
- Views: 12249
Re: Can't Get Stable Connection - VX II - OSE En.. & Bin Dumping
I'd say you would be correct.
- Thu Nov 11, 2010 12:09 am
- Forum: Holden ALDL ECUs
- Topic: Delco / Kalmaker 808 compatability
- Replies: 8
- Views: 4792
Re: Delco / Kalmaker 808 compatability
I did a multipiont conversion on a mates IH Scout with a 345 about 3yrs ago , using an '808' and 5d code. 12p code is on the to do list when I get the dyno up and running again. We used an RPT alloy intake from the states arleady set up to take injectors, modified an old point dissy to take a sigma ...
- Mon Sep 20, 2010 9:33 am
- Forum: General Tuning Discussion
- Topic: Knock Sensors - using V6 on V8
- Replies: 24
- Views: 15775
Re: Knock Sensors - using V6 on V8
I have used a V6 knock board on V8's before with varying results, mostly alot of false knock counts, but it still hears bad knock and pulls timing as well. I still have V6 knock board fitted to a turbo 355 stroker in my 80 series, it is turned off because of false triggering but I do use it if we ar...