Search found 515 matches
- Wed Dec 07, 2016 12:50 pm
- Forum: Holden ALDL ECUs
- Topic: 12P TPS issue?
- Replies: 26
- Views: 13740
Re: 12P TPS issue?
In your first post you say tps voltage at idle is 1.4 volts , should be around half that at idle.
- Thu Nov 24, 2016 10:58 pm
- Forum: Chip/Memcal Reading/Writing
- Topic: LS1 flash chip info help
- Replies: 2
- Views: 2799
Re: LS1 flash chip info help
Not sure on willam but with gq4x
vt to vy intel = 28f400bx-b
vz intel = 28f800bx-b
vt to vy intel = 28f400bx-b
vz intel = 28f800bx-b
- Fri Nov 11, 2016 9:05 pm
- Forum: Holden ALDL ECUs
- Topic: E40 VATS PATCH ADDRESS
- Replies: 8
- Views: 4505
Re: E40 VATS PATCH ADDRESS
I think the first 1024k is the engine operating system and second 256k is transmission operating system
The software I have reads them both together and saves as one bin file , if I want to load that 1280k file to efilive I need to knock 256k off it with hex editor and only engine parameters are shown
The software I have reads them both together and saves as one bin file , if I want to load that 1280k file to efilive I need to knock 256k off it with hex editor and only engine parameters are shown
- Fri Nov 04, 2016 6:20 pm
- Forum: Holden ALDL ECUs
- Topic: E40 VATS PATCH ADDRESS
- Replies: 8
- Views: 4505
Re: E40 VATS PATCH ADDRESS
That interesting 0x6000 > 0x8000 looks like security block
Thanks for the info
Thanks for the info
- Fri Nov 04, 2016 3:02 pm
- Forum: Holden ALDL ECUs
- Topic: E40 VATS PATCH ADDRESS
- Replies: 8
- Views: 4505
E40 VATS PATCH ADDRESS
Got an e40 pcm that I need to disable vats on , anyone know the o/s address where the patch is applied
- Sun Oct 09, 2016 12:04 am
- Forum: Chip/Memcal Reading/Writing
- Topic: can't burn stacked bin
- Replies: 21
- Views: 14576
Re: can't burn stacked bin
Are you using the usb lead gq4x came with , ive had similar problems with cheap shit usb leads
Does the chip id ok
Does the chip id ok
- Tue Oct 04, 2016 4:38 pm
- Forum: Delco ECU Conversions
- Topic: Ls1 ecu to 304 Motor
- Replies: 12
- Views: 16986
Re: Ls1 ecu to 304 Motor
Not sure , I think it does though.
If it does you could still use 8 coils
If it does you could still use 8 coils
- Tue Oct 04, 2016 3:29 pm
- Forum: Delco ECU Conversions
- Topic: Ls1 ecu to 304 Motor
- Replies: 12
- Views: 16986
Re: Ls1 ecu to 304 Motor
Ive never done it but ive heard you run pcm in lo res mode , use a vt dizzy with cam sig , and tie the coil outputs together with diodes
- Fri Sep 30, 2016 3:59 pm
- Forum: Ford ECUs
- Topic: PCMTec Development Blog
- Replies: 679
- Views: 543702
Re: Ford MPC565 Tuning
I made up a tunerpro adx that gets sae and dma pids for gm e38 pcm to suit my new can cable a few nights ago . The direct memory access pids are obtained with mode 23 , 32 bit address and 16 bit length request on e38. The adx I made was getting pids at a rate of 160 hz using mix of dma and sae pids....
- Fri Sep 30, 2016 1:30 pm
- Forum: Custom Code
- Topic: LPG injection
- Replies: 27
- Views: 31884
Re: LPG injection
What injectors did you use vn5000? I still have them in the shed , here is a pic of injectors and driver Was easy to wire up , one relay to switch between fuel pump and gas solonoids , and one relay to switch between petrol injectors and gas injectors , on gas the pcm controlled the gas solenoids f...