P01 '0411 12200411 v6 support
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: 12200411 tune Disassembly (12225074)
no its just a stock VR V6 cam sensor setup.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: 12200411 tune Disassembly (12225074)
Possibly different. I know the V8's running low res mode have a 4X crank trigger and a 1X cam from the dissy and the cam signal is half cam rotation looking at the chopper wheel on them.
Re: 12200411 tune Disassembly (12225074)
Here is a 4.3 V6 low res crank and cam pattern look like.
Here is the V8 low res crank and cam pattern.
Here is the V8 low res crank and cam pattern.
Last edited by Apples on Fri Nov 11, 2016 10:46 am, edited 1 time in total.
Don't make excuses. Make more horsepower.
Re: 12200411 tune Disassembly (12225074)
Thanks haven't got the V8 one too have you?
Re: 12200411 tune Disassembly (12225074)
Found picture of OEM V6 Low res crank sensor.
This is the 24x conversion sensor wheel
now if I can make it fit a V6 balancer.
here is the 24x sensor wheel to degrees.
This is the 24x conversion sensor wheel
now if I can make it fit a V6 balancer.
here is the 24x sensor wheel to degrees.
Don't make excuses. Make more horsepower.
Re: 12200411 tune Disassembly (12225074)
There's a model can't remember the name of V6 with the 0411 and it takes the 18X 3X crank and 1X cam. I'll see if I kept the link or maybe you're onto it all ready. Haven't followed the V6 to much so looked over it quickly.
Re: 12200411 tune Disassembly (12225074)
I haven't seen a V6 using 18x 3x and 1x cam on a 411 from the factory.
that's not to say they don't exist.
that's not to say they don't exist.
Don't make excuses. Make more horsepower.
Re: 12200411 tune Disassembly (12225074)
Fair chance I misread it. Would of been in the 1998 2002 era if it was.
Whats your plans anyway convert a V6 of yours to to the 0411? Once you have the trigger pattern sorted it's just like any other conversion.
Whats your plans anyway convert a V6 of yours to to the 0411? Once you have the trigger pattern sorted it's just like any other conversion.
Re: 12200411 tune Disassembly (12225074)
well my plan is to try and run a V6 with ls1 coils and 411 pcm with auto.
then later on add 3 bar mafless tune.
I want to do it with out opening and modding the pcm.
then later on add 3 bar mafless tune.
I want to do it with out opening and modding the pcm.
Don't make excuses. Make more horsepower.
Re: 12200411 tune Disassembly (12225074)
Sounds good keep us posted. Those low res trace pictures you posted. Do you have the whole manual for those models or just those images? Any chance you could PM a copy if you do?