$11 Definition Info and XDF
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
$11 Definition Info and XDF
The $11 code is used in VR V6 and V8 with automatic transmissions. It controls the 4L60E transmission along with the engine. The engine program is very similar to the VR $12 code, the main changes are for banked injection with a cam sensor. The V6 uses this while the V8 still uses batch injection where all 8 injectors are fired at once. The bins are 64k in size.
Bins
A list compiled by adrian of the various $11 bins and the code variant can be found here
Standard holden bins can be downloaded here
XDF For Editing In TunerPro
This is a fully featured TP4 XDF listing every single parameter available in the PCM, it uses categories and levels to try and make the XDF simpler to use. Its still a work in progress as the levels still need work along with some formatting of names. If you find any errors or would like to request a change please post here. The XDF works with the bins listed under variants 3, 4 and 5 of the post by adrian thats linked above. Other XDFs can be found here
ADX for Logging In TunerPro 5
Can be downloaded here
ALDL Hardware
ALDL Interface
Real-Time Tuning In TunerPro 5
Real-Time modified bins can be found here which are used with an NVRAM. For reading and writing in realtime use Antus' TunerPro 5 plugin, or for reading and writing use the FlashTool
Bins
A list compiled by adrian of the various $11 bins and the code variant can be found here
Standard holden bins can be downloaded here
XDF For Editing In TunerPro
This is a fully featured TP4 XDF listing every single parameter available in the PCM, it uses categories and levels to try and make the XDF simpler to use. Its still a work in progress as the levels still need work along with some formatting of names. If you find any errors or would like to request a change please post here. The XDF works with the bins listed under variants 3, 4 and 5 of the post by adrian thats linked above. Other XDFs can be found here
ADX for Logging In TunerPro 5
Can be downloaded here
ALDL Hardware
ALDL Interface
Real-Time Tuning In TunerPro 5
Real-Time modified bins can be found here which are used with an NVRAM. For reading and writing in realtime use Antus' TunerPro 5 plugin, or for reading and writing use the FlashTool
-
- Posts: 1217
- Joined: Sun Mar 15, 2009 10:20 am
- cars: 2004 VYII Acclaim Wagon V6 Auto LPG/Petrol
2004 VYII Berlina sedan V6 Auto
2005 VZ Monaro CV8 manual - Location: Geelong, VIC
Re: $11 Definition Info and XDF
Awesome work!!!
That is an unbelievably well defined xdf and layout.
That is an unbelievably well defined xdf and layout.
Re: $11 Definition Info and XDF
WOW Excellent work mate.
-
- Posts: 109
- Joined: Sat Mar 21, 2009 8:59 am
- cars: VX commodore
Re: $11 Definition Info and XDF
there are 4 lists for malf flags ,can some one explain these please
TRANS MALF MASK FLAGS, CEL ENABLE FLAGS, MALF FLAGS, TRANS MALF FLAG
another question
Run A/F Param - High Speed Fuel cutoff - Low Limit Is this road speed and units in kmh instead rpm?
TRANS MALF MASK FLAGS, CEL ENABLE FLAGS, MALF FLAGS, TRANS MALF FLAG
another question
Run A/F Param - High Speed Fuel cutoff - Low Limit Is this road speed and units in kmh instead rpm?
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: $11 Definition Info and XDF
Yep should have been KPH not RPM, fixed now
The flags are for processing the fault condition and then if the CEL should be displayed. There are two lots as the transmission code and engine code are kinda like two different systems, so there are two lots of flags.
The flags are for processing the fault condition and then if the CEL should be displayed. There are two lots as the transmission code and engine code are kinda like two different systems, so there are two lots of flags.
-
- Posts: 109
- Joined: Sat Mar 21, 2009 8:59 am
- cars: VX commodore
Re: $11 Definition Info and XDF
Can you give me a brief description on these codes?
TRANS MALF MASK FLAGS,
CEL ENABLE FLAGS,
MALF FLAGS,
TRANS MALF FLAG
TRANS MALF MASK FLAGS,
CEL ENABLE FLAGS,
MALF FLAGS,
TRANS MALF FLAG
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: $11 Definition Info and XDF
And In the updated XDF hover you mouse over the headings and it gives you a description. They just simply tell the PCM to process individual faults and if the fault is set to turn on the CEL.VL400 wrote:The flags are for processing the fault condition and then if the CEL should be displayed. There are two lots as the transmission code and engine code are kinda like two different systems, so there are two lots of flags.
-
- Posts: 2886
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: $11 Definition Info and XDF
This XDF is really well defined but I've found a bin that has some stuff not defined, does anyone know what it is in these area's?
I thought anything before the start of the cal area was normally ram, but not sure?
There's also a hell of a lot of stuff after 8FFE of which I though that start getting into the programming area?
I thought anything before the start of the cal area was normally ram, but not sure?
There's also a hell of a lot of stuff after 8FFE of which I though that start getting into the programming area?
- Attachments
-
- BMZA $11 strange bin diff's.jpg (146.44 KiB) Viewed 14738 times
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: $11 Definition Info and XDF
The $11 code is a little different and has program space before the cal, this is the reason the TP checksum does not work The items after 8FFE is also program space which starts at 0x9000.
-
- Posts: 6
- Joined: Thu Jan 19, 2012 12:26 am
- cars: Vr commodore v6
Re: $11 Definition Info and XDF
in looking at the setup everything is in MPH instead of KMH how do i change this?