Re: VY PCM - 16269238
Posted: Mon Jan 25, 2010 9:54 pm
by Mick
Bench Wiring/Programming VX and VY Holden V6 PCM
PCM Grounds:
*All these grounds are tied together in the engine harness 300mm from the PCM connectors.
*A05 = Black/Red
*B05 = Black/Red
*E07 = Black/Red
*F07 = Black/Red
……………………
C06 = Black/Yellow
D06 = Black
All grounds can be tied together and attached to Bat - Neg.
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
PCM BAT + 12V:
# Both of these battery positives are tied together 300mm from the PCM connectors. Both of these wires are attached to Bat + 12V permanently.
# C12 = Orange
# D12 = Orange
……………………
*Ignition switched Bat + 12v. This wire should be switched to resemble ignition being turned on and off. This is handy for soft reset of PCM when necessary. Switched on in run mode.
*D16 = Pink
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
PCM Serial Data Output:
This wire is connected to pin 9 of the ALDL connector. This wire carries communications to and from the PCM. (Mod Edit: this did say pin 16 which was incorrect! Thanks for the report Holden202T and Kojab).
C13 = Red/ Black
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
PCM Diagnostic:
This wire is connected to Pin 6 of the ALDL connector. It is a signal to the PCM to activate Diagnostic Mode.
D09 = White/ Black
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
ALDL Diagnostic Connector: Picture view of the front of the connector.
Pin 5 of the ALDL connector Black/ Yellow wire is connected to Bat- Neg. This is used to earth the PCM diagnostic output to ground via the Moates RS232 Interface. Pin 6 is connected to PCM Diagnostic input D09 = White/ Black wire.
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
You are only required to hook up 12 wires to power a VY or VX PCM for Diagnostic Simulation or Flash Programming. The PCM Pin Numbers are signified on the inside of the PCM connector sockets at the top left corner, A/B, C/D, E/F. There are 3 x connectors with 2 rows in each. The letters correspond to each row. The rows are number left to right.
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Thanks to Yodas great pictures I fixed up the pin out numbers for the ALDL connector.
Cheers
Mick