98 vt srs light

Post by **The1** » Tue Jan 21, 2014 4:39 pm

there is one here for BCM

http://pcmhacking.net/forums/viewtopic. ... bcm#p26820

One here for PCM

http://pcmhacking.net/forums/viewtopic. ... 2&t=12#p30

if i recall it was maybe pin 1

vs ss · Post by **vs ss** » Tue Jan 21, 2014 10:38 pm

Ok might be getting to deep here for me

Thanks for everyones help but I will continue studying it .

Post by **antus** » Tue Jan 21, 2014 11:21 pm

Do you have some kind of terminals that you can slot over the pins of the aldl interface?

Check the diagram here: http://en.wikipedia.org/wiki/On-board_d ... _connector

if you can connect pin 5 of the aldl interface to pin 5 in the car, and pin 9 of the aldl interface to pin 1 in the car, then send F2,56,A,AE with the flash tool that might do it. if you try it, let us know.

or if you can move pins in the obd port on the car, pop pin 1 and 9 out and install pin 1 in the position of 9 then try (swap back afterwards for normal logging).

vs ss · Post by **vs ss** » Tue Jan 21, 2014 11:43 pm

Thanks for that antus,yes I do have some terminals that fit over the pins in the cable so I will do that (hopefully tomorrow) and report back

Cheers.

Post by **The1** » Wed Jan 22, 2014 7:18 am

just checked, it's pin 1

vs ss · Post by **vs ss** » Wed Jan 22, 2014 4:22 pm

hi well i changed the pins and sent the command through but nothing happens.
I went and borrowed the reset tool from my old work and that reset so i know the system is ok but the car has gone now but i might drag my vs out of the shed and continue trying to work this out.
I can use the scan tool anytime i want so i was thinking if i tee into the aldl plug and use the flashtool whether i can catch the command?
Anyway thanks for your help so far

Cheers.

Post by **antus** » Wed Jan 22, 2014 4:32 pm

Yeah you can log the command that way. use the monitor chatter function of the flash tool.

Note that on later models you dont get a reply, but you power cycle the car and the light goes out (and comes back on again after a few seconds if the fault is still present).

vs ss · Post by **vs ss** » Wed Jan 22, 2014 9:31 pm

Hi antus,yes I was turning the power cycle to make sure as that is the same as the tool I used to use.
Well if I get time I will bring mine out from under the covers and do some more testing.
Cheers.

j_ds_au · Post by **j_ds_au** » Sat Feb 28, 2015 1:16 pm

vs ss wrote:hi well i changed the pins and sent the command through but nothing happens.
I went and borrowed the reset tool from my old work and that reset so i know the system is ok but the car has gone now but i might drag my vs out of the shed and continue trying to work this out.
I can use the scan tool anytime i want so i was thinking if i tee into the aldl plug and use the flashtool whether i can catch the command?
Anyway thanks for your help so far
Cheers.

Hi,

Which version of the command did you send? (Was the first byte F2?)

Joe.

98 vt srs light

Re: 98 vt srs light

Re: 98 vt srs light

Re: 98 vt srs light

Re: 98 vt srs light

Re: 98 vt srs light

Re: 98 vt srs light

Re: 98 vt srs light

Re: 98 vt srs light

Re: 98 vt srs light