VS-VY Enhanced Factory Bins
-
- Posts: 3427
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: VS-VY Enhanced Factory Bins
Yes they are 0-5 volt sensors.
Re: VS-VY Enhanced Factory Bins
Hello,
Are you sure these are 3 wire 0-5v sensor? The output does look linear but it appears to be a thermistor ohm output. I have hunted long and hard for a 0-5 linear output temp sensor.
Are you sure these are 3 wire 0-5v sensor? The output does look linear but it appears to be a thermistor ohm output. I have hunted long and hard for a 0-5 linear output temp sensor.
-
- Posts: 3427
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: VS-VY Enhanced Factory Bins
They are 2 wire same as the factory GM type sensor. On the website linked earlier it has all the info
Re: The1's Enhanced Factory Bins
yes please!!!!!!!!charlay86 wrote:Is anyone interested in flex fuel support?
-
- Posts: 1
- Joined: Fri Feb 04, 2022 1:08 pm
- cars: HSV W427, HSV SportsCAT SV, Holden VX Calais, Holden VY II Calais
- Location: Melbourne
Re: The1's Enhanced Factory Bins
I am, yes please. It would be awesome to be able to use E85 and have blend tables for timing, fueling, cranking etc.charlay86 wrote:Is anyone interested in flex fuel support?
-
- Posts: 4
- Joined: Wed Jun 17, 2020 9:30 pm
- cars: vy calais vy spac sedan vy spac ute
Ve omega
Re: VS-VY Enhanced Factory Bins
Having issues with changing to negative spark in the high and low octane tables for stupid crackle on decel on the vs v6 enhanced bin and xdf when I say set the decel tables to neg-15 and save it then reopen it it’s at 0 not-15 if there a max retard table somewhere im missing that needs to be changed like vx/vy v6 any help is appreciated
- antus
- Site Admin
- Posts: 8258
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: VS-VY Enhanced Factory Bins
if you are prepared to take the risk try the xdf for the non-enhanced version *of the same os*. The enhanced are patched, not rebuilds so items that work on the factory OS but are omitted from enhanced are probably still there and likely to work.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: VS-VY Enhanced Factory Bins
Unfortunately the factory code starts at 00 Hex as 0 spark. This changed with VT.encrypted wrote:Having issues with changing to negative spark in the high and low octane tables for stupid crackle on decel on the vs v6 enhanced bin and xdf when I say set the decel tables to neg-15 and save it then reopen it it’s at 0 not-15 if there a max retard table somewhere im missing that needs to be changed like vx/vy v6 any help is appreciated
You can work around it by using the Extended Intake Air tables to offset the spark into negative down low perhaps as ive codded them to allow negative.
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: VS-VY Enhanced Factory Bins
Has anybody worked out where the address location for DTC92 - Low speed fan communication failure is on the Flash Ecus?
Just to turn that processing off for when running flash pcms in standalone configuration without a bcm?
Just to turn that processing off for when running flash pcms in standalone configuration without a bcm?
Re: VS-VY Enhanced Factory Bins
Try these and let me know, if it's good then ill update the main page.hsv08 wrote:Has anybody worked out where the address location for DTC92 - Low speed fan communication failure is on the Flash Ecus?
Just to turn that processing off for when running flash pcms in standalone configuration without a bcm?
- Attachments
-
- VY_V6_$060A_Enhanced_v0.9h.xdf
- (319.76 KiB) Downloaded 175 times
-
- VX_V6_$BD_Enhanced_v0.9g.xdf
- (294.94 KiB) Downloaded 166 times