Injector Flow Testing Data
Re: Injector Flow Testing Data
set of 6 sold.
- Holden202T
- Posts: 10312
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Injector Flow Testing Data
definitely a lot better spray than the garden hose dekas
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Injector Flow Testing Data
yeh holes make all the difference
- vlad01
- Posts: 7830
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Injector Flow Testing Data
Any you recommend that are around that 60lb, shorter than stock by about 10mm?
Just toying with the idea of retracting the injector bosses in the VN-VR v6 manifold to allow opening up the runners right up in that area.
Just toying with the idea of retracting the injector bosses in the VN-VR v6 manifold to allow opening up the runners right up in that area.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Injector Flow Testing Data
those grey 12hole 80LB on the previous page are 14mm shorter. I have more of those in the post now just waiting to arrive.
- vlad01
- Posts: 7830
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Injector Flow Testing Data
Whats that other GM fomoco looking one next to the L67 injector? that looks shorter. 14mm shorter is probable too much. 10mm max or ideally around 7-8mm for what Im looking to do. Its so I can machine away the boss completely inside the runner.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Injector Flow Testing Data
im only aware of 3 standard sizes, Standard Length, 14mm shorter and then the tiny ones like LSX use. Im sure 4mm is neither here or there it should have room in the rail housing or can make enough room for that? The black Fomoco denso ones are same 14mm shorter as the grey denso ones.
-
- Posts: 3440
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: Injector Flow Testing Data
Why not just fit some spacers under the fuel rail mounting bolts to get your 7-8mm?vlad01 wrote:Whats that other GM fomoco looking one next to the L67 injector? that looks shorter. 14mm shorter is probable too much. 10mm max or ideally around 7-8mm for what Im looking to do. Its so I can machine away the boss completely inside the runner.
- vlad01
- Posts: 7830
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Injector Flow Testing Data
yeah I could just modify the rails. To suit.
Just ideas really.
Just ideas really.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Injector Flow Testing Data
here's the 3 sizes compared. End to End and between the Middle of the top and bottom Seal.