Speeduino PCB for Delco Replacement
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Speeduino PCB for Delco Replacement
I have been working on this one for a while, its a speeduino based ECU designed to take a delco 808 header, and the pin out matches a stock 808.
So after a bit of bench testing to prove it all works, i wanted to run it on a car to see that it does actually work, and the only one i had was the FX!
This is basically no tune other than enough that was needed to make it run!
[youtube]https://www.youtube.com/watch?v=mWS__MYZXYs[/youtube]
Theres a few small kinks to iron out but generally its a good thing and im pretty stoked!
So after a bit of bench testing to prove it all works, i wanted to run it on a car to see that it does actually work, and the only one i had was the FX!
This is basically no tune other than enough that was needed to make it run!
[youtube]https://www.youtube.com/watch?v=mWS__MYZXYs[/youtube]
Theres a few small kinks to iron out but generally its a good thing and im pretty stoked!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vlad01
- Posts: 7828
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Speeduino PCB for Delco Replacement
Nice work, always good to have more options, especially if it can expand on the already excellent 808 capabilities.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Speeduino PCB for Delco Replacement
You legend
Re: Speeduino PCB for Delco Replacement
Nice work ...
Intelligence is in the details!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
It is easier not to learn bad habits, then it is to break them!
If I was here to win a popularity contest, their would be no point, so I wouldn't be here!
-
- Posts: 590
- Joined: Thu Feb 13, 2020 11:32 pm
- cars: Mainly GM trucks, a Cruze and an Equinox for dailys..
Re: Speeduino PCB for Delco Replacement
Very damn impressive isn't even close to describing my admiration at your work, superb!!!
Re: Speeduino PCB for Delco Replacement
Impressive. What's the advantage of using this over a Delco?
"Definition of a Drag Racer: A person who spends money he doesn't have on parts he doesn't need to impress people he doesn't know." - Grumpy Jenkins----- Poverty---
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Speeduino PCB for Delco Replacement
it uses tunerstudio so probably a bit more user friendly than tunerpro is, but other than that probably no real differences to if you are using $12P ...
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Speeduino PCB for Delco Replacement
does it have spark cut and flex fuel abilities or the space to add in extras like that?
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Speeduino PCB for Delco Replacement
actually thats a good question, yes speeduino has spark cut, but i havent actually tested it, and flex fuel, i have used a GM flex fuel sensor on the speeduino that this is based off and its got the same circuit in it so it should also work, but it hasnt been tested.
I also connected some high current and low current outputs to the flex pins usually on $12P delco
also theoretically (not tested) with this you could use a 5V square wave crank trigger input, and then the EST output should be able to directly drive an LS1 coil.
I also connected some high current and low current outputs to the flex pins usually on $12P delco
also theoretically (not tested) with this you could use a 5V square wave crank trigger input, and then the EST output should be able to directly drive an LS1 coil.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Speeduino PCB for Delco Replacement
Nice def interested in that. I’d be keen to buy a unit and test it. What sort of loads can it drive on the flex outputs?