I will try here for the linkages you asked about.
Hopefully you can see what you are looking for, this is my GT, however sedan linkages are very similar over here.
| Attachments: |
|
GT Engine 001.JPG [ 1.31 MiB | Viewed 19971 times ] |
| bellett.net https://delcohacking.net/forums/ |
|
| Bellett Sweden https://delcohacking.net/forums/viewtopic.php?f=4&t=2898 |
Page 1 of 1 |
| Author: | 1968GT [ Tue Nov 18, 2014 11:16 pm ] | ||
| Post subject: | Bellett Sweden | ||
I will try here for the linkages you asked about. Hopefully you can see what you are looking for, this is my GT, however sedan linkages are very similar over here.
|
|||
| Author: | Glenn [ Wed Nov 19, 2014 12:33 am ] |
| Post subject: | Re: Bellett Sweden |
1968GT wrote: I will try here for the linkages you asked about. Hopefully you can see what you are looking for, this is my GT, however sedan linkages are very similar over here. that looks familiar, Dave 
|
|
| Author: | 1968GT [ Wed Nov 19, 2014 1:01 am ] |
| Post subject: | Re: Bellett Sweden |
I wonder why Glenn!!  The fellow from Sweden wanted a look at the mechanical linkages for the clutch, the best I can do, not very good, apparently in Sweden the Belletts had hydraulic clutch. |
|
| Author: | 67GT [ Wed Nov 19, 2014 1:42 am ] |
| Post subject: | Re: Bellett Sweden |
I noticed that in one of his earlier photos, that they have two master cylinders. I thought that must have been an after market job. |
|
| Author: | KJB [ Wed Nov 19, 2014 2:12 am ] | ||
| Post subject: | Re: Bellett Sweden | ||
This pic may be a bit clearer. KB
|
|||
| Author: | BULLITT [ Wed Nov 19, 2014 6:57 am ] |
| Post subject: | Re: Bellett Sweden |
nice clean engine bay Kerry .... |
|
| Author: | KJB [ Wed Nov 19, 2014 7:38 am ] |
| Post subject: | Re: Bellett Sweden |
Didn't you see Daves' engine bay .....? THAT is CLEAN ! KB |
|
| Author: | BULLITT [ Wed Nov 19, 2014 10:11 am ] |
| Post subject: | Re: Bellett Sweden |
yes I saw daves ....ive seen Lewis's also ..now im going outside to sulk ....they all look good ...cheers davo |
|
| Author: | 1968GT [ Wed Nov 19, 2014 9:50 pm ] |
| Post subject: | Re: Bellett Sweden |
Good upon you KJB, that is a far better photo than mine, thank you. Dave |
|
| Author: | Bellett Sweden [ Wed Nov 19, 2014 10:07 pm ] |
| Post subject: | Re: Bellett Sweden |
Thanks for the pics! Really nice engine bay guys! Your brake cylinder is similar to our clutch cylinders, wonder if I can brake with it...? if I can find a cross...? How many exits have your cross? including the brake light switch? |
|
| Author: | Bellett Sweden [ Wed Nov 19, 2014 10:14 pm ] |
| Post subject: | Re: Bellett Sweden |
Now I feel ashamed of my engine bay   
|
|
| Author: | mrflibbles [ Wed Nov 19, 2014 10:32 pm ] |
| Post subject: | Re: Bellett Sweden |
your engine bay is nothing to be ashamed of! mines a lot worse! |
|
| Author: | Bellett Sweden [ Wed Nov 19, 2014 10:45 pm ] |
| Post subject: | Re: Bellett Sweden |
Check in 1968gt and kerrys engine bay there is a bit difference... There are some differences between right and left hand drive cars 
|
|
| Author: | Bellett Sweden [ Fri Dec 19, 2014 9:33 pm ] |
| Post subject: | Re: Bellett Sweden |
Does anyone have a picture of how the clutch works? I'm curious
|
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|