| Author |
Message |
|
sdoubleb
Joined: Fri Jul 10, 2015 10:04 am
Posts: 85
Location: Kanmantoo South Australia
Car(s): 67 bellett
|
Ok trying to remove the front guards off the new rust bucket pretty sure I've got all the bolts, did they use sealer an glue these frigging things on at the factory cause these will not budge ?
|
| Mon Aug 31, 2015 11:17 am |
|
|
|
rod
Joined: Thu Feb 05, 2009 11:36 am
Posts: 579
Car(s): 68gt coupe , 98 toyota prado
|
you need to take doors off first ....as there are bolts you need to get out cant get these out with door on ....
|
| Mon Aug 31, 2015 11:24 am |
|
|
|
sdoubleb
Joined: Fri Jul 10, 2015 10:04 am
Posts: 85
Location: Kanmantoo South Australia
Car(s): 67 bellett
|
Yeah doors don't wanna come off either haha need a impact driver but I did get the 4 bolts out without removing door
|
| Mon Aug 31, 2015 11:49 am |
|
|
|
CQGT
Joined: Sun Dec 12, 2010 10:04 am
Posts: 386
Location: Boyne Island.Gladstone. Queenland
Car(s): '70 PR91,'69 PR20 x 2,'66 PR20,'65? KR20's x 2,'66 ? PR90,2012 d22 STR Navarra.
|
There are 5 bolts. 6mm with 10mm hex. 1 is tucked up under the guard near the bottom of the "A" pillar. The other 4 are in front of the door. There is also a 8mm bolt and nut, 12mm hex, on the bottom. In the assembly they used a sealant that can be broken by using a thin bladed tool such as a putty knife. Your on a big learning curve. I still am. Don't be afraid to ask questions.
Dave.
_________________
CQGT.
I'm the Dave with the convertible.
|
| Mon Aug 31, 2015 12:48 pm |
|
|
|
Stickman
Joined: Fri Apr 10, 2009 11:29 pm
Posts: 1524
Location: Kallangur, Brisbane QLD
Car(s): 3x1965 PR20(Donkey, Jenny n Bundy) 1 1969 PR20(Percy) 2 1968 PR20(Eugine n GT Donor) 1 1968 PR91 GT, 1 1965 Wasp
|
Impact driver is always a handy bit of kit but sometimes even it needs the helping hand of the screws being preheated with an oxy first (get em red hot them let them cool, breaks the rust. Then give em a whack with the impact driver)
_________________
1xB+1xE+2xL+1xE+2xT=BELLETT
RUST isn't a crime
www.gartdesign.com.au
|
| Tue Sep 01, 2015 3:47 am |
 
|
|
|
sdoubleb
Joined: Fri Jul 10, 2015 10:04 am
Posts: 85
Location: Kanmantoo South Australia
Car(s): 67 bellett
|
Hmm might have missed the 1 by a" pillar. Got a impact driver today and a 4ltr wd40 today  so will let it have it tonight.
|
| Tue Sep 01, 2015 5:03 am |
|
|
|
sdoubleb
Joined: Fri Jul 10, 2015 10:04 am
Posts: 85
Location: Kanmantoo South Australia
Car(s): 67 bellett
|
Had a win... Did have all the bolts out. Sealant holding front guards on looked like sikaflex had the hit a sharp knife around joins using a mallet  . Got door off with persuading it with blow torch and impact driver. On to the other side now
Attachments:
14413586123251305682809.jpg [ 2.49 MiB | Viewed 18897 times ]
|
| Fri Sep 04, 2015 9:28 am |
|
|
|
flying
Joined: Mon Nov 15, 2010 3:11 am
Posts: 259
Location: Adelaide
Car(s): 1967 GT Bellett
|
Looks tidier than most
Keep up the good work
Cheers
Flying
|
| Fri Sep 04, 2015 10:01 am |
|
|
|
yellowperil
Joined: Tue Sep 29, 2009 10:15 am
Posts: 280
Location: Hobart
Car(s): 1970 Bellett, 1968 Bellett, Triumph Stag, 1940 Traction Avant, T Ford 1938 Pontiac plus the usual modern stuff
|
Well done. Sometimes it can be a pain getting stuff off. Bolts and nuts are often not obvious but then you had to solve the sealant problem. It's good to see you wanting to do a strip down as you find so much stuff that will only cause problems later. Good luck with it. It all looks good from your pics.
YP
_________________
Bellett SEDANS are proof that the gods love us and want us to be happy.
|
| Sun Sep 06, 2015 7:21 am |
|
|
