 |
|
Page 1 of 1
|
[ 11 posts ] |
|
| Author |
Message |
|
RobSA
Joined: Sat Sep 26, 2009 10:55 am
Posts: 580
Location: Adelaide
Car(s): BA Falcon, 68 Bellett
|
I've searched and cannot find it, so.
What is the head bolt tension for the standard G150 in the Belletts?
Cheers Rob
_________________
If you can't fix it with a hammer, you have an electrical problem!
|
| Sun Sep 18, 2016 9:24 am |
|
|
|
Asroc66
Joined: Tue Jun 18, 2013 5:09 am
Posts: 428
Location: Sydney NSW
Car(s): PR91 1967 GT, PR20 1966 1/2 with GT Goodies
|
Hi Rob
I think I recall standard is 7kgm = 50 ft lbs
I go higher to about 9-10kgm = 68-72 ft lbs
Depends on 'feel', Belletts have heapem big head bolts.
Best to
- clean out the thread with a tap
- use Assembly lube on the thread and under the head
Bolt (at a push could use engine oil but not quite as good)
Cheers
J
_________________
To increase the fun, add a hair dryer
Last edited by Asroc66 on Mon Sep 19, 2016 3:34 am, edited 1 time in total.
|
| Sun Sep 18, 2016 12:14 pm |
|
|
|
mrflibbles
Joined: Mon Jan 05, 2009 10:39 am
Posts: 1136
Location: Adelaide Hills
Car(s): GU Patrol, AU ute, 1969 florian deluxe, 1976 Luv & 1980 KB 4x4 isuzu
|
yeah in the manual its 6-7 kgm
Im pretty sure i did mine a bit tighter though.
_________________
I am "that" Florian guy.
never buy a car you cant push.
|
| Mon Sep 19, 2016 3:06 am |
|
|
|
RobSA
Joined: Sat Sep 26, 2009 10:55 am
Posts: 580
Location: Adelaide
Car(s): BA Falcon, 68 Bellett
|
Thank you everyone for the info.
Cheers
Rob
_________________
If you can't fix it with a hammer, you have an electrical problem!
|
| Mon Sep 19, 2016 10:45 am |
|
|
|
RobSA
Joined: Sat Sep 26, 2009 10:55 am
Posts: 580
Location: Adelaide
Car(s): BA Falcon, 68 Bellett
|
So does anyone have the correct tension for the rocker stand bolts ?
_________________
If you can't fix it with a hammer, you have an electrical problem!
|
| Sun Jan 08, 2017 9:44 am |
|
|
|
Teditor
Joined: Tue Jul 05, 2011 1:01 pm
Posts: 368
|
I'm going back a long time, but the G150 has two head bolt sizes if I recall, 17mm for the 3 Bearing and 19mm for the 5 bearing, so I would assume two different settings, be careful about overtightening.
Ted (Teditor) Freeman
_________________
Ted Freeman
|
| Sun Jan 08, 2017 10:51 am |
|
|
|
67GT
Joined: Sun Jun 14, 2009 8:44 am
Posts: 348
Location: central coast
Car(s): 1967 bellett gt, wasp trayback , 2018 d-max 4x4 dual cab LSU, 2016 Focus, 1996 GQ Patrol
|
Hi Rob,
I do have that information, but it is at work.
If I don't remember to post later, call meon 02 4393 2833
Warren.
|
| Sun Jan 08, 2017 7:33 pm |
|
|
|
Early GT
Joined: Sat Oct 30, 2010 5:37 am
Posts: 265
Location: Gold Coast, Qld
Car(s): 1966 Bellett GT, 1968 Bellett GT, 2017 Subaru Levorg 2.0 GTS
|
Here is the table of tightening torques for 5 bearing engines,
Cheers,
Lewis.
Attachments:
image.jpeg [ 391.98 KiB | Viewed 24435 times ]
|
| Sun Jan 08, 2017 7:56 pm |
|
|
|
RobSA
Joined: Sat Sep 26, 2009 10:55 am
Posts: 580
Location: Adelaide
Car(s): BA Falcon, 68 Bellett
|
Yippee. Thank you so much 
_________________
If you can't fix it with a hammer, you have an electrical problem!
|
| Sun Jan 08, 2017 8:53 pm |
|
|
|
67GT
Joined: Sun Jun 14, 2009 8:44 am
Posts: 348
Location: central coast
Car(s): 1967 bellett gt, wasp trayback , 2018 d-max 4x4 dual cab LSU, 2016 Focus, 1996 GQ Patrol
|
Lewis beet me to it.
That is the same book I have.
|
| Mon Jan 09, 2017 4:27 am |
|
|
|
RobSA
Joined: Sat Sep 26, 2009 10:55 am
Posts: 580
Location: Adelaide
Car(s): BA Falcon, 68 Bellett
|
Tis good 67GT Wish it was easier to clean the head and block of the accumulated gunk. 40+ degrees then constant rain ... blah. Hard to get anything done at all. Head is nice and clean now. Next is to clean bolts and rocker gear, then if I can get some fine weather, the block. Cheers everyone
_________________
If you can't fix it with a hammer, you have an electrical problem!
|
| Fri Jan 13, 2017 3:27 am |
|
|
|
|
Page 1 of 1
|
[ 11 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 8 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
|
